Interlux Pacifica Plus
Pacifica Plus is a copper free ablative antifouling with dual antifouling properties: Econea (tm) for the control of barnacles and shell fouling, and Biolux� Slime Blocking Technology. It...
Description
Pacifica Plus is a copper free ablative antifouling with dual antifouling properties: Econea (tm) for the control of barnacles and shell fouling, and Biolux� Slime Blocking Technology. It is a fast-drying, low VOC, high solid ablative antifouling which minimizes paint build-up. Suitable for all boats including sail, power and ideal for aluminum pontoon boats. � Econea is a trademark of Johnson and Johnson.
PRODUCT�DESCRIPTION Pacifica�Plus�is�a�copper�free�antifouling�that�provides�excellent�protection�from�shell�and�weed�fouling.�It�uses�Biolux��technology�to�block�slime�and�Econea� to ward off barnacles and zebra mussels. The fast dry formula of Pacifica Plus allows the boat to be painted and launched quickly and its ablative action reduces paint build up and helps to improve fuel efficiency. Pacifica�Plus�is�available�in�bright�colors�and�is�suitable�for�use�on�all�boats�including�fiberglass,�aluminum, wood and steel and can be used in all waters. Pacifica Plus can be brush or roller applied.�
PRODUCT�INFORMATION
Color YBB263�Black
Finish Low�sheen
Specific�Gravity 1.7
Volume�Solids 65.94%
Typical�Shelf�Life 2�yrs
VOC�(As�Supplied) 330�g/lt
APPLICATION�AND�USE
Preparation
BARE�ALUMINUM�Sandblast�or�sand�with�medium�grade�(grit)�emery�cloth�to�a�bright�metal�finish�and�wipe�clean.�Apply one�coat�of�Interprotect�2000E�that�has�been�thinned�15�20%�with�Reducing�Solvent�2316N.�Apply�the�Interprotect�the same�day�as�blasting�or�sanding.
FACTORY�FINISHED�ALUMINIUM�Prime�with�Primocon.�
BARE�FIBERGLASS�Begin�by�scrubbing�the�surface�thoroughly�with�a�stiff�brush�using�soap�and�water�to�remove�loose dirt�and�contamination.�Flush�with�fresh�water�to�remove�the�soap�residue.�Remove�mold�release�wax�using�one�of�the following�methods:� Apply�Fiberglass�Surface�Prep�YMA601�or�Low�VOC�Fiberglass�Solvent�Wash�202V�with�a�maroon,�3M�Scotch�Brite� pad�and�scrub�well.�Flush�with�fresh�water�or�wipe�off�with�a�clean,�wet�cloth�ensuring�that�no�traces�of�Fiberglass Surface�Prep�or�Low�VOC�Fiberglass�Solvent�Wash�remain. or An�alternate�method�would�be�to�dampen�cheesecloth�with�Fiberglass�Solvent�Wash�202.�Wipe�thoroughly�to�remove�all surface�contamination�and�cleaners.�Wipe�off�with�a�clean,�dry�rag�before�liquid�dries.�Wipe�only�a�few�square�feet�at�a time�and�change�rags�frequently.�To�be�certain�the�contamination�has�been�removed,�run�water�over�the�surface.�If�the water�beads�up�or�separates,�repeat�one�of�the�above�methods.�When�the�water�sheets�off,�all�contamination�has�been removed.�Repair�all�scratches,�nicks�and�dings�by�sanding�those�areas�with�80�grade�(grit)�paper.�Remove�sanding residue�with�Fiberglass�Solvent�Wash�202.�Fill�the�repair�areas�with�Interlux��Watertite�Epoxy�filler.
No�Sand�System���Clean�surface�as�above.�Apply�one�coat�of�Interlux�Interprotect�2000E.�When�the�Interprotect�2000E is�thumbprint�tacky�apply�the�first�coat�of�Pacifica�Plus.�Apply�the�second�coat�of�Pacifica�Plus�allowing�the�appropriate dry�times�between�coats. Sanding�System���Clean�surface�as�above.�Sand�entire�gel�coat�well�with�80�grit�sandpaper�until�a�flat,�matte�finish�is obtained.�Wipe�surface�clean.�Repair�imperfections�with�Interlux��Watertite�(YAV135).�Sand�and�wipe�clean.
BARE�WOOD�Sand�with�80�grade�(grit)�paper.�Clean�with�Special�Thinner�216.�Apply�first�coat�reduced�10%�with Special�Thinner�216.�Fill�seams,�if�necessary,�with�Seam�Compound�Brown�30.�
PREVIOUSLY�PAINTED�SURFACES In�Good�Condition�with�Pacifica�or�Trilux�33�Sand�with�80�(grit)�grade�paper.�Wipe�with�Special�Thinner�216.�TBT Copolymers�If�these�coatings�are�more�than�a�year�old,�wet�sand�the�surface�with�80�(grit)�grade�paper�to�a�clean,�firmly attached�surface.�Wipe�down�with�Special�Thinner�216.�Apply�1�2�coats�of�TBT�Sealer.�Non�TBT�Copolymers�Apply�1 coat�of�Primocon.�Hard�Antifoulings�Sand�surface�with�80�grade�(grit)�paper�to�a�clean�firmly�attached�surface,�wipe with�Special�Thinner�216.�Apply�Pacifica�Plus.� In�Poor�Condition�Remove�antifouling�paint�in�poor�condition.�Sand�and�wipe�clean�with�Fiberglass�Solvent�Wash�202.�
STEEL�Contact�the�Interlux�Technical�Service�Department�at�1�800�468�7589�for�full�information.�
�
Method
At�least�2�coats�should�be�applied.�Apply�an�extra�stripe�coat�in�areas�of�high�wear�such�as�chines,�rudders,�sterngear and�any�leading�edges.
Hints
Thinner�Special�Thinner�216.�
Thinning�Do�not�exceed�10%�maximum.�
Airless�Spray�Pressure:�170�204�bar/2500�3000�psi.�Tip�Size:�0.53�mm/0.021"�
Conventional�Spray�Pressure:�3.44�4.47�bar/50�65�psi�(gun�pressure)?�10�15�psi�(pot�pressure).�Tip�Size:�1.8�2.2 mm/0.071�0.087"� Other�To�prevent�premature�failure,�ensure�correct�amount�of�paint�is�applied�using�the�coverage�as�a�guide.
Some�Important�Points Product�temperature�should�be�minimum�5�C/41�F�and�maximum�35�C/95�F.� Ambient�temperature�should�be�minimum�5�C/41�F�and�maximum�35�C/95�F.� Substrate�temperature�should�be�minimum�5�C/41�F�and�maximum�35�C/95�F.�
Do�not�use�below�5�C/41�F.
�
Compatibility/Substrates Apply�to�clean,�dry,�properly�prepared�surfaces�only.�Surface�must�be�dry�and�clean,�and�free�from�grease,�loose�paint etc.�Do�not�apply�Pacifica�Plus�directly�to�aluminum.�All�metal�surfaces�must�be�primed�with�Interprotect�2000E/2001E�or Primocon.�Do�not�apply�direct�to�tin�based�paint�such�as�Micron��33,�Micron��44�or�Tri�Lux��IIT.
Number�of�Coats 2�coats,�3�on�bare�wood(first�coat�thinned)
Coverage
(Theoretical)���536�square�feet�per�gallon�per�coat�at�2.0�mils�dft
Recommended�DFT�per�coat 2�mils�dry
Recommended�WFT�per�coat 3�mils�wet
Application�Methods Airless�Spray,�Brush,�Conventional�Spray,�Roller� DO�NOT�SPRAY�without�following�proper�safety�procedures�for�spray�application.�
Specifications
Specifications
| Brand | Interlux |
|---|---|
| Category | Paints - Bottom Paint |
| SKU | INT-YBB260G |
| UPC / Barcode | 0081948000048 |
| Available color | Blue, Black, Gray |
| Available option | Gallon, Pint, Quart |
Shipping & Returns
Shipping: Most orders ship within 1 business day from Cape May, NJ.
Returns: 30 days from delivery, unused with tags. Text us at (609) 884-0330 or email hello@seagearmarine.com.
Local pickup: Free in-store pickup at our Marine Supply or Outfitters location in Cape May.
Reviews
Scroll down to read verified customer reviews.
View all reviews →